Back to blog
Regulations & Compliance

Hazard Assessment Alberta: Lessons From a $114K Fine

November 17, 20269 min read
Two oil and gas workers in hi-vis reviewing a written hazard assessment on a clipboard at an Alberta oil battery at dusk, beside a dark brushed-steel panel with the headline Written. Repeated. In Plac

If you are an Alberta employer asking what a hazard assessment must include, the short answer is this: it must be done before work begins, written down with the controls you will use, dated, and repeated when the work changes. Those duties sit in Part 2 of the Occupational Health and Safety Code, and they are the duties Alberta OHS is still prosecuting after serious oilfield injuries.

A recent case shows why. On October 6, 2026, the Government of Alberta announced that Artis Exploration Ltd. was fined $114,000, including the victim fine surcharge, after a worker was seriously injured in an explosion and fire at an oil battery site on May 10, 2024. The company pleaded guilty as an employer on October 1 in the Red Deer Court of Justice to one count under the OHS Code about hazard assessment and control. All other charges were withdrawn (Red Deer Advocate, October 6, 2026).

This article walks through what Part 2 asks of you, what the case tells employers, and a practical checklist for keeping hazard assessments written, current and backed by controls that are actually in place.

What happened in the Artis Exploration case

The facts reported so far are short, and it is worth sticking to them.

  • The incident: a worker was seriously injured in an explosion and fire at an oil battery site on May 10, 2024.
  • The outcome for Artis: a $114,000 fine, including the victim fine surcharge, announced October 6, 2026. The guilty plea was entered October 1 in the Red Deer Court of Justice.
  • The charge: one count under the OHS Code about hazard assessment and control. The other charges were withdrawn.
  • The appeal window: either side has 30 days to appeal.
  • A second employer: Synergy Well Servicing Ltd. faces four OHS counts over the same incident. Its hearing is set for November 18, 2026 in Red Deer.

Synergy's charges have not been decided, and nothing here should be read as a finding against it. What we can say is that two employers are before the court over one incident, which is the everyday reality of a multi-employer oil and gas site.

Why this matters beyond oil and gas

The case is about the most basic duty in the Code. It was not a rare technical rule. It was the requirement to assess hazards and control them. That duty applies to a three-person landscaping outfit and a drilling contractor in exactly the same way, which is why a fine like this is worth a look from any Alberta employer.

The takeaway is that Alberta OHS is still prosecuting the basic duty to assess and control hazards after serious injuries. If your assessments exist only in the safety manager's head, or were written once in 2022 and never touched, that is the gap to close.

Hazard assessment in Alberta: what OHS Code Part 2 requires

Part 2 of the Code is titled Hazard Assessment, Elimination and Control. Read it in full on the Government of Alberta's OHS legislation site. The sections that matter most are 7, 8 and 9.

Section 7: assess before work begins, then write it down

Section 7(1) requires an employer to assess a work site and identify existing and potential hazards before work begins at the site, or before a new site is built. The government's handbook for employers puts it plainly, and also notes that the person doing the assessment needs training to recognize, evaluate and control hazards (Hazard Assessment and Control handbook).

Then the paperwork duties:

  • 7(2): prepare a report of the results of the hazard assessment and the methods used to control or eliminate the hazards identified.
  • 7(3): record the date the assessment was prepared or revised on the document.
  • 7(4): repeat the assessment at reasonably practicable intervals to prevent unsafe and unhealthy working conditions, when a new work process is introduced, and when a work process or operation changes. Check the section for the full list of triggers.

Notice what that last one means in practice. A hazard assessment is not a one-time form. A new piece of equipment, a new contractor on the lease, a change in the order of work or a shift in conditions can all be reasons to revisit it.

Section 8: involve the workers

Section 8(1) requires an employer to involve affected workers in the hazard assessment and in the control or elimination of the hazards identified. The people doing the job usually know where the real hazards are. An assessment written at a desk, without them, tends to miss things that show up on day one.

Section 9: eliminate first, then control

Section 9 requires employers to eliminate hazards whenever it is reasonably practicable to do so. If elimination is not reasonably practicable, the hazards must be controlled. The Government of Alberta's explanation guide for Part 2 describes it the same way.

This is the step many assessments stumble on. Naming a hazard is the easy part. The control has to be real, assigned to someone, and in place on the day the work happens. A control that exists only on paper does not protect the worker standing next to the equipment.

Multi-employer sites: where assessments get lost

The Artis and Synergy matter involves two employers connected to one incident. Without drawing conclusions about either, it highlights a pattern any contractor or operator should plan for: when several employers share a site, each one still has its own duties, and hazards can fall between them.

Practical points for shared sites:

  1. Know who is on site. Keep a current list of every employer and contractor working at the location.
  2. Share the hazard assessments. Each employer's crew should see the site hazards that affect them, including those created by the other companies' work.
  3. Reassess when someone new arrives. A new contractor starting work is a change to the work process. Treat it as a trigger to review.
  4. Agree how you will communicate. Pre-job meetings and daily tailgates only work if the right people are in the room.
  5. Check that controls are in place, not just agreed. Walk the site and look.

A practical checklist to keep your hazard assessments defensible

Use this as a starting point and adapt it to your operations.

  • [ ] A written hazard assessment exists for every site and task type you work on.
  • [ ] Each one is dated, with the date of every revision recorded.
  • [ ] Workers who do the job helped build it.
  • [ ] Every identified hazard has an elimination or control listed, with a person responsible.
  • [ ] Controls are checked in the field, not assumed.
  • [ ] There is a trigger list for reassessing: new process, changed process, new contractor, new equipment, a near miss, a change in conditions.
  • [ ] The assessment is reviewed at regular intervals even when nothing seems to have changed.
  • [ ] Supervisors can show you the current version at the work site, not just in the office.
  • [ ] Multi-employer sites have a shared communication routine.

How to run the review in a week

If you suspect your assessments are out of date, you do not need a major project. Try this:

  1. Day 1: list your active sites and task types, and pull the current assessment for each.
  2. Day 2: check the dates. Anything undated or older than your review interval goes to the top of the pile.
  3. Day 3 and 4: walk two or three sites with the crew. Compare the paper with what you see. Note every new hazard and every control that is missing.
  4. Day 5: update the documents, record the dates, and brief the crews at the next tailgate.

Repeat it on a schedule. The goal is a living record that matches the work.

Frequently asked questions

What is a hazard assessment under the Alberta OHS Code?

It is the assessment of a work site to identify existing and potential hazards, required by section 7 of the OHS Code. The employer must prepare a report of the results and the methods used to control or eliminate the hazards identified.

How often do I have to repeat a hazard assessment in Alberta?

Section 7(4) requires it to be repeated at reasonably practicable intervals, when a new work process is introduced, and when a work process or operation changes, among other triggers listed in the section. There is no single fixed number of months, so set an interval that fits your work and follow it.

Do workers have to be involved in the hazard assessment?

Yes. Section 8(1) requires an employer to involve affected workers in the hazard assessment and in the control or elimination of the hazards identified.

What is the difference between eliminating and controlling a hazard?

Under section 9, you must eliminate a hazard when it is reasonably practicable to do so. If that is not reasonably practicable, you must control it. Elimination removes the hazard. Control reduces the risk while the hazard remains.

Was Artis Exploration fined for a missing hazard assessment?

The reported charge was one count under the OHS Code about hazard assessment and control, to which the company pleaded guilty. The source does not say more about the specific failing, so we will not guess. Read the original report for the details available.

How TruStar can help

TruStar Safety works with Alberta employers on the practical side of Part 2: building written hazard assessments that crews actually use, reviewing the ones you already have, and setting up the reassessment routine described above. If your company is working toward COR or SECOR, a gap review of your hazard assessment process is one of the most useful first steps. TruStar does not conduct COR or SECOR certification audits, but we help you prepare for them. A fractional safety manager can also own the schedule so it does not slip when the field gets busy.

TruStar Connect, our safety and operations app, keeps hazard assessments, inspections, incident reports and toolbox talks in one place, with dates recorded and the current version in every supervisor's pocket. You can try it free at connect.trustarsafety.com.

Ready to look at your own assessments? Contact TruStar Safety to book a conversation.

This article is general information, not legal advice. Check the current OHS Act, Regulation and Code and your own site conditions. Details of the Artis Exploration and Synergy Well Servicing matters come from the Red Deer Advocate report linked above; the Synergy charges have not been decided.

Need help with this on your site?

Our certified safety professionals can build the programs, training, and documentation to put this into practice.